BAS standards at public enquiry
Institute for Standardization of Bosnia and Herzegovina, on the proposal of BAS technical committees, announces a public enquiry on draft national standards (stage code 40.20).
Deadline for submission of comments on draft national standards is 60 days from the publication of the enquiry on the Institute's website (if necessary, it can be shortened to no less than 30 days).
The drafts of BAS standards are available to our stakeholders via online module for reading the draft of BAS standards, and basic information about the draft (title, scope, technical committee that prepared the draft for public discussion, etc.) is available on the ISBIH website.
The request for access to the draft BAS standard at the public enquiry should be sent to email: stand@isbih.gov.ba. To be able to access the online module for reading the draft BAS standards, you must be registered on our website.
Written comments on the draft national standards (with the designation of BAS technical committee and the reference designation of the BAS draft standards) shall be submitted to the Institute.
To fill this form correctly, see the Comment Form Use Guide.
Standard reference | Stage code | BAS/TC | Real date | Forseen date for next stage code |
---|---|---|---|---|
nsBAS IEC TS 62600-202:2025 Marine energy - Wave, tidal and other water current converters - Part 202: Early stage development of tidal energy converters - Best practices and recommended procedures for the testing of pre-prototype scale devices | 40.20 | BAS/TC 56 | 16.05.2025 | 16.07.2025 |
nsBAS IEC TS 62788-2:2025 Measurement procedures for materials used in photovoltaic modules - Part 2: Polymeric materials - Frontsheets and backsheets | 40.20 | BAS/TC 56 | 16.05.2025 | 16.07.2025 |
nsBAS IEC TS 62788-6-3:2025 Measurement procedures for materials used in photovoltaic modules - Part 6-3: Adhesion testing for PV module laminates using the single cantilevered beam (SCB) method | 40.20 | BAS/TC 56 | 16.05.2025 | 16.07.2025 |
nsBAS IEC TS 62788-8-1:2025 Measurement procedures for materials used in photovoltaic modules - Part 8-1: Electrically conductive adhesive (ECA) - Measurement of material properties | 40.20 | BAS/TC 56 | 16.05.2025 | 16.07.2025 |
nsBAS IEC TS 62804-2:2025 Photovoltaic (PV) modules - Test methods for the detection of potential-induced degradation - Part 2: Thin-film | 40.20 | BAS/TC 56 | 16.05.2025 | 16.07.2025 |
nsBAS IEC TS 62915:2025 Photovoltaic (PV) modules - Type approval, design and safety qualification - Retesting | 40.20 | BAS/TC 56 | 16.05.2025 | 16.07.2025 |
nsBAS IEC TS 62950:2025 Household and similar electrical appliances - Specifying smart capabilities of appliances and devices - General aspects | 40.20 | BAS/TC 57 | 30.04.2025 | 30.06.2025 |
nsBAS IEC TS 63106-2:2025 Simulators used for testing of photovoltaic power conversion equipment - Recommendations - Part 2: DC power simulators | 40.20 | BAS/TC 56 | 16.05.2025 | 16.07.2025 |
nsBAS IEC TS 63202-3:2025 Photovoltaic cells - Part 3: Measurement of current-voltage characteristics of bifacial photovoltaic cells | 40.20 | BAS/TC 56 | 16.05.2025 | 16.07.2025 |
nsBAS IEC TS 63202-4:2025 Photovoltaic cells - Part 4: Measurement of light and elevated temperature induced degradation of crystalline silicon photovoltaic cells | 40.20 | BAS/TC 56 | 16.05.2025 | 16.07.2025 |
nsBAS IEC TS 63209-2:2025 Photovoltaic modules - Extended-stress testing - Part 2: Polymeric component materials | 40.20 | BAS/TC 56 | 16.05.2025 | 16.07.2025 |
nsBAS IEC TS 63290:2025 Supplementary requirements for intelligent assemblies | 40.20 | BAS/TC 52 | 23.04.2025 | 23.06.2025 |
nsBAS IEC TS 63342:2025 C-Si photovoltaic (PV) modules - Light and elevated temperature induced degradation (LETID) test - Detection | 40.20 | BAS/TC 56 | 16.05.2025 | 16.07.2025 |
nsBAS IEC TS 63397:2025 Photovoltaic (PV) modules - Qualifying guidelines for increased hail resistance | 40.20 | BAS/TC 56 | 16.05.2025 | 16.07.2025 |
nsBAS ISO 10009:2025 Quality management — Guidance for quality tools and their application | 40.20 | BAS/TC 3 | 28.04.2025 | 27.06.2025 |
nsBAS ISO 1018:2025 Coal - Determination of moisture-holding capacity | 40.20 | BAS/TC 27 | 14.04.2025 | 13.06.2025 |
nsBAS ISO 10303-1:2025 Industrial automation systems and integration — Product data representation and exchange — Part 1: Overview and fundamental principles | 40.20 | BAS/TC 51 | 24.04.2025 | 23.06.2025 |
nsBAS ISO 10303-101:2025 Industrial automation systems and integration — Product data representation and exchange — Part 101: Integrated application resource: Draughting | 40.20 | BAS/TC 51 | 24.04.2025 | 23.06.2025 |
nsBAS ISO 10303-113:2025 Industrial automation systems and integration — Product data representation and exchange — Part 113: Integrated application resource: Mechanical features | 40.20 | BAS/TC 51 | 24.04.2025 | 23.06.2025 |
nsBAS ISO 10303-2:2025 Industrial automation systems and integration — Product data representation and exchange — Part 2: Vocabulary | 40.20 | BAS/TC 51 | 24.04.2025 | 23.06.2025 |