BAS standards at public enquiry
Institute for Standardization of Bosnia and Herzegovina, on the proposal of BAS technical committees, announces a public enquiry on draft national standards (stage code 40.20).
Deadline for submission of comments on draft national standards is 60 days from the publication of the enquiry on the Institute's website (if necessary, it can be shortened to no less than 30 days).
The drafts of BAS standards are available to our stakeholders via online module for reading the draft of BAS standards, and basic information about the draft (title, scope, technical committee that prepared the draft for public discussion, etc.) is available on the ISBIH website.
The request for access to the draft BAS standard at the public enquiry should be sent to email: stand@isbih.gov.ba. To be able to access the online module for reading the draft BAS standards, you must be registered on our website.
Written comments on the draft national standards (with the designation of BAS technical committee and the reference designation of the BAS draft standards) shall be submitted to the Institute.
To fill this form correctly, see the Comment Form Use Guide.
Standard reference | Stage code | BAS/TC | Real date | Forseen date for next stage code |
---|---|---|---|---|
nsBAS EN ISO 6401:2025 Plastics - Poly(vinyl chloride) - Determination of residual vinyl chloride monomer using gas-chromatographic method | 40.20 | BAS/TC 50 | 25.02.2025 | 24.04.2025 |
nsBAS EN ISO 6806:2025 Rubber hoses and hose assemblies for use in oil burners - Specification | 40.20 | BAS/TC 50 | 25.02.2025 | 24.04.2025 |
nsBAS EN ISO 7965-1:2025 Packaging - Drop test - Part 1: Paper sacks | 40.20 | BAS/TC 50 | 25.02.2025 | 24.04.2025 |
nsBAS EN ISO 8028:2025 Rubber and/or plastics hoses and hose assemblies for airless paint spraying - Specification | 40.20 | BAS/TC 50 | 25.02.2025 | 24.04.2025 |
nsBAS EN ISO 8256:2025 Plastics - Determination of tensile-impact strength | 40.20 | BAS/TC 50 | 25.02.2025 | 24.04.2025 |
nsBAS EN ISO 9773:2025 Plastics - Determination of burning behaviour of thin flexible vertical specimens in contact with a small-flame ignition source | 40.20 | BAS/TC 50 | 25.02.2025 | 24.04.2025 |
nsBAS IEC TR 60099-10:2025 Surge arresters - Part 10: Rationale for tests specified by IEC 60099-4:2014 | 40.20 | BAS/TC 8 | 12.03.2025 | 12.05.2025 |
nsBAS IEC TR 60216-7-2:2025 Electrical insulating materials - Thermal endurance properties - Part 7-2: Accelerated determination of relative thermal endurance using analytical test methods (RTEA) - Results of the round robin tests to validate procedures of IEC TS 60216-7-1 by non-isothermal kinetic analysis of thermogravimetric data | 40.20 | BAS/TC 8 | 12.03.2025 | 12.05.2025 |
nsBAS IEC TR 61328:2025 Live working - Guidelines for the installation of transmission and distribution line conductors and earth wires - Stringing equipment and accessory items | 40.20 | BAS/TC 8 | 12.03.2025 | 12.05.2025 |
nsBAS IEC TR 61643-03:2025 Low-voltage surge protective devices - Part 03: SPD Testing Guide | 40.20 | BAS/TC 8 | 12.03.2025 | 12.05.2025 |
nsBAS IEC TS 61934:2025 Electrical insulating materials and systems - Electrical measurement of partial discharges (PD) under short rise time and repetitive voltage impulses | 40.20 | BAS/TC 8 | 12.03.2025 | 12.05.2025 |
nsBAS IEC/IEEE 63253-5713-8:2025 Station Service Voltage Transformers (SSVT) | 40.20 | BAS/TC 8 | 12.03.2025 | 12.05.2025 |
nsBAS ISO 11359-1:2025 Plastics — Thermomechanical analysis (TMA) — Part 1: General principles | 40.20 | BAS/TC 50 | 25.02.2025 | 24.04.2025 |
nsBAS ISO 11359-2:2025 Plastics — Thermomechanical analysis (TMA) — Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature | 40.20 | BAS/TC 50 | 25.02.2025 | 24.04.2025 |
nsBAS ISO 11359-3:2025 Plastics — Thermomechanical analysis (TMA) — Part 3: Determination of penetration temperature | 40.20 | BAS/TC 50 | 25.02.2025 | 24.04.2025 |
nsBAS ISO 14427:2025 Carbonaceous materials used in the production of aluminium — Cold and tepid ramming pastes — Preparation of unbaked test specimens and determination of apparent density after compaction | 40.20 | BAS/TC 49 | 20.03.2025 | 19.05.2025 |
nsBAS ISO 14606:2025 Surface chemical analysis — Sputter depth profiling — Optimization using layered systems as reference materials | 40.20 | BAS/TC 49 | 20.03.2025 | 19.05.2025 |
nsBAS ISO 14714:2025 Essential oils and aromatic extracts - Determination of benzene content | 40.20 | BAS/TC 23 | 24.03.2025 | 23.05.2025 |
nsBAS ISO 17109:2025 Surface chemical analysis — Depth profiling — Method for sputter rate determination in X-ray photoelectron spectroscopy, Auger electron spectroscopy and secondary-ion mass spectrometry sputter depth profiling using single and multi-layer thin films | 40.20 | BAS/TC 49 | 20.03.2025 | 19.05.2025 |
nsBAS ISO 17544:2025 Carbonaceous materials used in the production of aluminium — Cold and tepid ramming pastes — Determination of rammability of unbaked pastes | 40.20 | BAS/TC 49 | 20.03.2025 | 19.05.2025 |