BAS standards at public enquiry

Institute for Standardization of Bosnia and Herzegovina, on the proposal of BAS technical committees, announces a public enquiry on draft national standards (stage code 40.20).

Deadline for submission of comments on draft national standards is 60 days from the publication of the enquiry on the Institute's website (if necessary, it can be shortened to no less than 30 days).

The drafts of BAS standards are available to our stakeholders via online module for reading the draft of BAS standards, and basic information about the draft (title, scope, technical committee that prepared the draft for public discussion, etc.) is available on the ISBIH website. 

The request for access to the draft BAS standard at the public enquiry should be sent to email: stand@isbih.gov.ba. To be able to access the online module for reading the draft BAS standards, you must be registered on our website.

Written comments on the draft national standards (with the designation of BAS technical committee and the reference designation of the BAS draft standards) shall be submitted to the Institute. 

To fill this form correctly, see the Comment Form Use Guide.

Showing 261-280 of 347 items.
Standard referenceStage codeBAS/TCReal dateForseen date for next stage code
   
nsBAS EN ISO 3785:2024
Metallic materials - Designation of test specimen axes in relation to product texture
40.20BAS/TC 431.05.202429.07.2024
nsBAS EN ISO 3995:2024
Metallic powders - Determination of green strength by transverse rupture of rectangular compacts
40.20BAS/TC 431.05.202429.07.2024
nsBAS EN ISO 4064-1/A11:2024
Water meters for cold potable water and hot water - Part 1: Metrological and technical requirements
40.20BAS/TC 3820.06.202418.08.2024
nsBAS EN ISO 4064-2/A11:2024
Water meters for cold potable water and hot water - Part 2: Test methods
40.20BAS/TC 3820.06.202418.08.2024
nsBAS EN ISO 4064-5/A11:2024
Water meters for cold potable water and hot water - Part 5: Installation requirements
40.20BAS/TC 3820.06.202418.08.2024
nsBAS EN ISO 4491-1:2024
Metallic powders - Determination of oxygen content by reduction methods - Part 1: General guidelines
40.20BAS/TC 431.05.202429.07.2024
nsBAS EN ISO 4491-2:2024
Metallic powders - Determination of oxygen content by reduction methods - Part 2: Loss of mass on hydrogen reduction (hydrogen loss)
40.20BAS/TC 431.05.202429.07.2024
nsBAS EN ISO 52120-1:2024
Energy performance of buildings - Contribution of building automation, controls and building management - Part 1: General framework and procedures (ISO 52120-1:2021, Corrected version 2022-09)
40.20BAS/TC 5124.04.202416.06.2024
nsBAS EN ISO 5667-1:2024
Water quality - Sampling - Part 1: Guidance on the design of sampling programmes and sampling techniques
40.20BAS/TC 717.05.202417.07.2024
nsBAS EN ISO 5755:2024
Sintered metal material - Specifications
40.20BAS/TC 431.05.202429.07.2024
nsBAS EN ISO 5842:2024
Powder metallurgy - Hot isostatic pressing - Argon detection using gas chromatography and mass spectrometry techniques
40.20BAS/TC 431.05.202429.07.2024
nsBAS EN ISO 6975:2024
Natural gas - Extended analysis - Gas-chromatographic method
40.20BAS/TC 3104.06.202403.08.2024
nsBAS EN ISO 6976:2024
Natural gas - Calculation of calorific values, density, relative density and Wobbe indices from composition
40.20BAS/TC 3104.06.202403.08.2024
nsBAS EN ISO 7704:2024
Water quality - Requirements for the performance testing of membrane filters used for direct enumeration of microorganisms by culture methods
40.20BAS/TC 717.05.202417.07.2024
nsBAS EN ISO 80000-1:2024
Quantities and units - Part 1: General
40.20BAS/TC 3820.06.202418.08.2024
nsBAS EN ISO 80000-11:2024
Quantities and units - Part 11: Characteristic numbers
40.20BAS/TC 3820.06.202418.08.2024
nsBAS EN ISO 80000-3:2024
Quantities and units - Part 3: Space and time
40.20BAS/TC 3820.06.202418.08.2024
nsBAS EN ISO 8062-3:2024
Geometrical product specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 3: General dimensional and geometrical tolerances and machining allowances for castings using ± tolerances for indicated dimensions
40.20BAS/TC 431.05.202429.07.2024
nsBAS HD 60269-2/A1:2024
Low-voltage fuses - Part 2: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) - Examples of standardized systems of fuses A to K
40.20BAS/TC 1821.05.202410.07.2024
nsBAS HD 60269-3/A2:2024
Low-voltage fuses - Part 3: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household or similar applications) - Examples of standardized systems of fuses A to F
40.20BAS/TC 1821.05.202410.07.2024